enterasys d2g124-12 manual

enterasys d2g124-12 manual

Handling the Switch To prevent electrostatic damage, attach an ESD wrist strap to your wrist before handling the D2 switch. Switch Components As shown in Figure 1 and Figure 2, ports and power supply receptacles are located on the rear panel of the D2 switch. Port, CPU, and power LEDs are visible from the front, top, and rear panels of the switch. Figure 1 D2 Switch (rear view) shown without optional enclosure The example used here describes connecting to two power sources. These LEDs are visible from the back of the switch as shown in If the initialization process is successful, the CPU LED turns green. If the CPU LED does not turn green, refer to the Enterasys D2 Hardware Installation Guide for troubleshooting information.The D2-PWR-POE is the only supply needed to power the D2G124-12P with PoE support. Both power supplies must be of the same type to support redundancy. Completing the Setup and Downloading the Latest Firmware Once you have connected power to the D2 switch and verified LED activity, you can complete the setup process as follows.Basic Setup Commands Table 1 Refer to the Enterasys D2 CLI Reference for more information. Table 1 Required CLI Setup Commands Step Task CLI commands 1 Set a new password For example, you can easily designate specific ports for guest users where they will only be able to obtain an IP address and access the web and at a lower quality of service than you provide to your enterprise users. To download Policy QuickStart go to: Each combo SFP port in use on the switch eliminates the availability of one RJ45 port. In other words, only 12 ports can be active at any given time. When an SFP transceiver (Mini-GBIC) SFP port 11 establishes a link, RJ45 port 11 is disabled. When an SFP transceiver (Mini-GBIC) in SFP port 12 establishes a link, RJ45 port 12 is disabled.

http://intermeetingsys.com/intermeeting/userfiles/dishwasher-installation-manual-bosch.xml

Tags:
• enterasys d2g124-12 manual, enterasys d2g124-12 manual, enterasys d2g124-12 manual transmission, enterasys d2g124-12 manual user, enterasys d2g124-12 manual pdf, enterasys d2g124-12 manuals.

By providing LEDs on the front, back, and top of the switch, the D2 offers very flexible mounting options (rack, wall, desktop, or under- tabletop), including an integral Kensington lock and an optional lock box for secure mounting. In order to provide a reliable, high-availability network, both the standard and Power over Ethernet (PoE) D2 models support redundant, external power bricks as well as Link Aggregation Groups (LAGs) for scalable, redundant uplinks. In conjunction with its non-blocking architecture, the D2’s robust Quality of Service (QoS) features enable strong support for converged multimedia networks, including Voice over IP (VoIP), video, as well as all types of data-intensive applications. Making use of Enterasys’ policy capabilities (included with every D2 after October 1st, 2011), a network administrator can define distinct roles or profiles that represent industry-specific operational groups such as a school or a business. Each defined role is granted individualized access to specific network services and applications (e.g., administrative staff, teacher, student, guest) and these access privileges remain associated with users as they move across both wired and wireless network access points. Users are authenticated via IEEE 802.1X, MAC address, or web authentication, and then assigned a pre-defined operational role ensuring that each user has access to appropriate information, thus aligning network resource utilization with business goals and priorities.Gigabit Ethernet Workgroup L2 Switch with Policy SupportSecurity Convergence. Refer to the Release Notes shipped wit h your device to determine which features are supported. Te c h n o l o g y.Courier font Used for examples of information displayed on the screen. Note: Calls the reader ’s attention to any item of information that may be of special importance. Caution: Contains information essential to avoid dama ge to the equipment.Refer to p age.

http://zao-tamp.ru/images_admin/fck/dishwasher-manual-kenmore-model-665_pdf.xml

D-Series CLI Overview 1-1 Switch Manageme nt Methods 1-1 Factory Default Settings 1-2 Using the Command Line Interface 1-5 CDP authentication code Set to 00-00 -00-00-00-00-00-00 CDP hold time Set to 180 seconds. CDP interval T ransmit frequency of CDP messages set to 60 seconds. Cisco discovery protocol Auto enabled on all ports. Cisco DP hold time Set to 180 seconds. Cisco DP interval ti mer Set to 60 seconds. Community name Public. Console (serial) port required settin gs Baud rate: 9600 Data b its: 8 Flow control: disabl ed S top bits: 1 Parity: none DHCP server Disabled. EAPOL Disabled. EAPOL authentication mode When enabled, set to auto for all ports. GARP time r Join timer set to 20 centiseconds; leave time r set to 60 centiseconds; leaveall timer set to 1000 centiseconds. GVRP Globally enabl ed. History buffer size 20 lines. IEEE 802.1 authentication Disabled. IGMP snooping Disabled. When enabled, query in terva l is set to 2 60 seconds and respon se time is set to 10 seconds. IP mask and gateway Subnet mask set to 0.0. 0.0; default gateway set to 0.0.0.0. IP routes No static routes configured. Jumbo frame support Enabled on all ports. Link aggregation control protocol (LACP) Enabled. Link aggregation admin key Set to 32768 for all ports. Link aggregation system priority Set to 32768 for all ports. Link aggregation outport algorithm Set to DIP-SIP. Lockout Set to disable Read-Write and Read -Onl y users, and to lockout the default admin (Super User) account for 15 minutes, after 3 failed login attempts. Logging Syslog port set to UDP port number 514. Logging severity level set to 6 (significant conditions) for all applications. MAC aging time Set to 300 seconds. MAC locking Disabled (globall y and on all ports). Passwords Set to an empty string for all defa ult user accounts. User must press ENTER at the password prompt to access CLI. Password aging Disabled. Password history No passwords are checked for duplication.

http://fscl.ru/content/canon-powershot-pro-1-service-manual

Policy classification Classification rule s are automatically enabled when created. Port auto-negotiation Enabled on all ports. Port advertised ability Maximum ability advertised on all ports. Port broadcast suppressi on Enabled and set to limit br oadcast packets to 14,881 per second on all switch ports. Port duplex mode Set to half duplex, except fo r 100BASE-FX and 1000BASE-X, which is set to full duplex. Port priori ty Set to 0. Port speed Set to 10 Mbps, except for 100 0BASE-X, which is set to 1000 Mbp s, and 100BASE-FX, which is set to 100 Mbp s. Port trap All ports are enabled to send link traps. Power over Ethernet port admin state Administrative state is on (auto). Priority classifi cation Classification ru les are automatically enabled when created. RADIUS client Disabled. RADIUS last resort actio n When the client is enab led, set to Challenge. RADIUS retries When the client is enab led, set to 3. RADIUS timeout When the client is enabled, set to 20 seconds. Rate limiting Disabled (globally and on all ports). SNMP Enabled. SNTP Disabled. S panning Tree Globally enabled and enabled on all ports. T able 1-1 Default Settings for Basic Switch Opera tion (Continued) Feature Default Setting If a S panning T ree BDPU is not rece ived on the port within a few seconds, the status setting changes to true. S panning Tree edge port delay Enabled. S panning Tree forward delay Set to 15 seconds. S panning Tree hello interval Set to 2 seconds. S panning Tree ID (SID) Set to 0. S panning Tree maximum aging time Set to 20 seconds. S panning Tree port priority All ports with bridge priority are set to 128 (medium priority). S panning Tree priority Bridge pri ority is set to 32768. S panning Tree topology change trap suppression Enabled. S panning Tree version Set to mstp (Multiple S panning Tree Protocol). SSH Disabled. System baud rate Set to 9600 baud. System contact Set to empty string. System location Set to empty string. System name Set to empty string.

https://gpwestlondon.com/images/compaq-armada-1592dt-manual.pdf

T erminal CLI display set to 80 columns and 24 rows. T imeout Set to 5 minutes. User names Login accounts set to ro for Read-Only access; rw for Read-W rite access; and admin for Super User access. VLAN dynamic egress Disabled on all VLANs. VLAN ID All ports use a VLAN id entifier of 1. Host VLAN Default host VLAN is 1. T able 1-1 Default Settings for Basic Switch Opera tion (Continued) Feature Default Setting Configured ? User ? Account ” ? on ? page 1 ? 6. Figure 1- 1 D-Series S t artup Screen Connecting Using Telnet Once.D ? Series ? switch ? allows ? yo u ? to ? di splay ? usage ? and ? syntax ? information ? for ? individual ? commands ? by ? typing ? help ? or ? ? ? after ? th e ? command. ? CLI Command Defaults Descriptions Each. Administrators with Super User (su) access can use the set system login command (p age 2-4) to create and change user accounts, and the set password command to change any local account password. Refer to p age. Quick S tart Setup Commands 2-1 Setting User Accounts and Pa sswords 2-2 Setting Basic Switch Prop erties 2-8 Activati ng Licensed Features 2-27 Configuring System Power and Power over Ethernet (PoE) 2-30 Downloading a Firmware Imag e 2-33 Reviewing and Selecting a Boot Firmw are Image 2-36 S tarting and Configuring T el net 2-37 Managing Switch Configuration and Fil es 2-39 Clearing and Closing the CLI 2-49 Resetting the Switch 2-50 Using and Configuring WebView 2-51 T able 2-3 Required CLI Setup Commands Step Ta s k CLI commands Refer to pa g e.. 1 Set a new p assword.Refer to p age. show system login 2-3 set system login 2-4 clear system login 2-4 set password 2-5 set system password length 2-6 set system pas sword aging 2-6 set system password history 2-7 show system lockout 2-7 Password history size Number of previously used user l ogin passwords that will be checked fo r duplication whe n the set password command is executed. Configured with set system password history ( page 2-7 ).

Password aging Number of days user passwords will remain valid before aging out. Configured with set system password aging ( p age 2-6 ). Username Logi n user names. Access Access assigned to this user accoun t: super-user, read-w rite or read-only. S tate Whether this user account is enabled or disabled. Mode Switch ? command, ? super ? user. username Specifies.Ta b l e 2 ? 5 ? provides ? an ? explanation ? of ? the ? command ? output. ?. size Specifies ? the ? number ? of ? passwords ? checked ? for ? duplication. ? Va l i d ? va lu e s ? are ? 0 ? to ? 10. Lockout attempts Number of failed login attempts allowed before a read -write or read-only user ’s account will be disabled. Lockout time Number of minutes the default adm in user account will be locked out after the maximum login attempts. For information about. Refer to p age. show ip address 2-9 set ip address 2-9 clear ip address 2-10 show ip protocol 2-1 1 set ip protoc ol 2-1 1 show system 2-12 show system hardware 2-13 show system utilization 2-13 show system enhancedbuffermode 2-15 set system enhancedbuffermode 2-15 show time 2-16 set time 2-16 show summertime 2-17 set summertime 2-17 set summertime date 2-18 set summertime recurring 2-18 clear summertime 2-19 set prompt 2-20 show banner motd 2-20 set banner motd 2-21 clear banner motd 2-21 show version 2-22 Refer to p age. Note: The D2 does not support the ability for a user to configure the host's gateway to be a local routed interface IP. The ho st's gateway must exist on a different device in the network if on e is configured. Sets ? the ? system’ s ? default ? gatew ay ? (next ? hop ? device). System contact Contact person for the system. Def ault of a blank string can be changed with the set system contact command (“ set system contact ” on page 2-24). System location Where the system is located. De fault of a blank string can be changed with the set system location command (“ set system location ” on page 2-23).

System name Name identifying the system. Defaul t of a blank string can be changed with the set system name command (“ set system name ” on page 2-23). PWR1-A S tatus Operational status for the power supply conn ected to PWR1-A on the switch. PWR1-B S tatus Operational status for the power supply conn ected to PWR1-B on the switch. PWR2-A S tatus Operational status for the power supply conn ected to PWR2-A on the switch. Fanx-S tatus Operational status of the fan(s). (This output not in use for the D2.) Uptime d,h:m:s System uptime. Logout T ime a n idle console or T elnet CLI session w ill remain connected before timing out. Default of 5 minutes can be changed with the set logout command (“ set logout ” on page 2-26). T able 2-6 show system Output Det ails (Continued) Output What It Di splays. Specifies ? the ? amount ? of ? time ? in ? minutes ? to ? offset ? daylight ? savings ? time ? from ? the ? non ? daylight ? saving s ? time ? system ? setting. ? Va l i d ? va l u e s ? are ? 1 ??? 1440. Default s None. Mode Switch ? command, ? read ? write. Note: Banner message text must be enclosed in beginnin g and ending doub le quotation marks. The message itself cannot contain any additional double quotation marks.Slot Module slot number (if applica ble) Port Number of ports supported. Model Switch’s model number.Makes ? this ? setting ? persistent ? for ? all ? fut ure ? sessions ? (writte n ? to ? NV ? RAM). Displa ys ? the ? type ? of ? flow ? control. parity (Optional) ? Displa ys ? the ? type ? of ? parity. stopbi ts (Optional). Displays ? the ? number ? of ? stop ? bits. Enterasys ? supplies ? a ? license, ? it ? wil l ? be ? sent ? to ? you ? as ? a ? character ? string ? similar ? to ? the ? following: INCREMENT D2Policy 2006.0127 27-jan-2011 0123456789AB 0123456789AB The.Refer to p age. set license 2-28 show license 2-29 clear license 2-30 Con sult the Installation Guide shipped with your product to determine if it is PoE-equipped. Refer to p age.

show inlinepower 2-31 set inlinepower threshold 2-31 set inlinepower trap 2-32 show port inlinepower 2-32 set port inlinep ower 2-33 threshold.Select an option. If no sele ction in 2 seconds then operational code will start. 1 - Start operational code. 2 - Start Boot Menu.Default s None. Mode Switch ? command, ? read ? only. Note: Y ou will not be able to peform th ese steps remotely unless you ha ve remote console support. Refer to p age. show boot system 2-36 set boot system 2-37 Refer to p age. show telnet 2-38 set telnet 2-38 telnet 2-39 Refer to p age. show snmp persistmode 2-40 set snmp persistmode 2-41 save conf ig 2-41 dir 2-42 show file 2-43 show config 2-44 configure 2-45 copy 2-45 delet e 2-46 show tf tp settings 2-46 set tftp timeout 2-47 clear tftp timeout 2-47 set tftp retry 2-48 clear tftp retry 2-48 Specifies ? the ? file ? name ? or ? directory ? to ? list. Use 'show config all' to sho w both default and non-default configurat ions. Displays ? default ? and ? non ? def ault ? configuration ? settings. facility (Optional). Specifies ? the ? exact ? name ? of ? one ? facility ? for ? which ? to ? show ? configuration. ? For ? example, ? enter ? “router ” ? to ? show ? only ? router ? configuration. outfile (Optional).Mode Switch ? command, ? read ? write. filename Specifies.Default s None. Mode Switch ? command, ? read ? only. filename Specifies.Default s None. seconds Specif ies.Refer to p age. cls 2-49 exit 2-49 Default s None. Mode Switch ? command, ? read ? write. For information about. Refer to p age. reset 2-50 clear config 2-51 Mode Switch ? command, ? read ? write. For information about.SSL, ? rege nerates ? new ? keys, ? and ? then ? restarts ? SSL. Refer to p age. Configuring CDP 3-1 Configuring Cisco Disco very Protocol 3-6 For information about. Refer to p age.

show cdp 3-1 set cdp st ate 3-3 set cdp auth 3-3 set cdp interval 3-4 set cdp hold-time 3-5 clear cdp 3-5 show neighbors 3-6 CDP Global S tatus Whether CDP is globally auto-e nab led, enabled or disabled. The default state of auto-enabled can be reset with the set cd p state command. For details, refer to “ set cdp st ate ” on page 3-3. CDP V ersions Supported CDP version number(s) supported by the switch. CDP Hold Time Minimum time interval (in seco nds) at which CDP configuration messages can b e set. The default of 180 seconds can be reset with the set cdp hold-time command. For details, refer to “ set cd p hold-time ” on p age 3-5. CDP Authentication Code Authentication code for CDP discovery protocol. The default of 00-00-00-00-00-00 - 00-00 can be reset using the set cdp auth command. For details, refer to “ set cdp auth ” on page 3-3. CDP T ransmit Frequency Frequency (in second s) at which CDP message s can be transmitted. The default of 60 seconds can be rese t with the set cdp interval comma nd. For details, refer to “ set cdp interv al ” on page 3-4. Port Port designation. For a detailed description of possible port-stri ng values, refer to “Port S tring Syntax Used in the CLI ” on page 4-1. T able 3-8 show cd p Output Det ails (Continued) Output Fi eld What It Displays.Refer to p age. show ciscodp 3-7 show ciscodp port info 3-8 set ciscodp status 3-9 set ciscodp timer 3-9 set ciscodp hold time 3-10 set ciscodp port 3-10 clear ciscodp 3-12 T able 3-9 show ciscod p Output Details Output Fi eld What It Displays. CiscoDP Whether Cisco DP is globally enabled or disabled. Auto indicate s that Cisco DP will be globally enabled only if Cisco DP PDUs are received. Default setting of a uto-enabled can be reset wi th the se t ciscodp st atus command. Holdtime Number of seconds neighbo ring devices will hold PDU tran smissions from the sending device. Defa ult value of 180 can be changed wi th the set c iscodp hold time command.

Device ID The MAC address of the switch. Last Change The time that the last Cisco DP neighbor was disco vered. T able 3-9 show ciscod p Output Details (Continued) Output Fi eld What It Displays.Port Port designation. For a detailed description of possible port-stri ng values, refer to “ Port S tring Syntax Used in the CLI ” on page 4-1. S tate Whether Cisco DP is enabled, disabled or auto -enabled on the p ort. Default state of enabled can be changed using the set ciscodp port command.Default of none can be changed using the set ciscodp port command. Defaul t of tru sted can be changed usin g the set cis codp port command.The default of 0 can be changed using the set ciscodp port command. T able 3-10 show ciscod p port info Output Deta ils (Continued) Output Fi eld What It Displays.Refer to p age. show port 4-4 show port status 4-4 show port counters 4-5 For a detailed descripti on of possible port-string values, refer to “ Port S tri ng Syntax Used in the CLI ” on page 4-1. Alias (truncated) Alias configured fo r the port. For details on using the set port alias command, refer to “ set port alias ” on page 4-9. Oper S tatus Operating status (up or down). Admin S tatus Wh ether the specified port is enabled (up) or disabled (down ). For details on using the set port disable command to change the default port status of enabled, refer to “ set port disable ” on page 4- 7. For details on using the set port enable comman d to re-enable ports, refer to “ set port enable ” on page 4-8. S peed Operational speed in Mbps or Kbps of the specified port. For details on using the set port speed command to change defa ults, refer to “ set port speed ” on p age 4-10. Duplex Duplex mode (half or full) of the specifi ed port. For details on using the set port duplex command to change defaults, refer to “ Setting Auto-Negotiation and Advertised Ability ” on page 4-14. T ype Physical port and i nterface type.

For a detailed descripti on of possible port-string values, refer to “ Port S tri ng Syntax Used in the CLI ” on page 4-1. MIB2 Interface MIB2 interface designation. Bridge Port IEEE 802.1D bridge port designati on. T able 4-12 show port counters Outpu t Det ails (Continued) Output Field What It Displays.. For information about. Refer to p age. set port disable 4-7 set port enable 4-8 show port alias 4-8 set port alias 4-9 port.For information about. Refer to p age. show port speed 4-10 set port speed 4-10 show port duplex 4-1 1 set port duplex 4-14 Refer to p age. show port jumbo 4-12 set port jum bo 4-13 clear port jumbo 4-13 port.Refer to p age. show port negotiation 4-14 set port negotiation 4-15 show port advertise 4-15 set port advertise 4-16 clear port advertise 4-17 Refer to p age. show flowcontrol 4-18 set flowcontrol 4-19 Refer to p age. show port trap 4-20 set port tra p 4-20 show linkflap 4-21 set linkflap globalstate 4-23 set linkflap portstate 4-24 set linkflap interval 4-24 set linkflap action 4-25 Port Port designation. LF S tatus Link flap enabled state. Actions Actions to be taken if the port violates allowed link flap behavior. Threshold Number of link down transitions necessary to trigger the link flap action. Interval T ime interval (in seconds) for accumulating link do wn transitions. Downtime Interval (in seconds) port(s) will be held down after a link flap violation. T able 4-14 show linkflap me trics Output De t ails Output Fi eld What it displays. Port Port designation. LinkS tatus Link status according to the link flap function. CurrentCount Link down count accruing toward the link flap th reshold. T o talCount Number of link downs since system start, T imeElapsed T ime (in seconds) since the last link down event. Violations Number of link flap violations on listed ports since system start.Refer to p age.

show port broadcast 4-29 set port broadcast 4-29 clear port broadcast 4-30 Caution: Port mirroring configuration should be performed only by person nel who are knowledgeable about the effects of port mi rroring and its impact on network operation. Caution: T raffic mirrored to a VLAN may contain control traffic. This may be interpreted by the downstream neighbor as legal control frames. It is recommended that you disable any protocols (such as S panning T ree) on inter-switch connections that might be affected. Refer to p age. show port mirroring 4-31 set port mirroring 4-32 clear port mirroring 4-33 This will prevent the ability to snoop traffic across multiple hops.Otherwise, the proper operation of the network could be at risk. Note: A given link is al located to, at most, on e Link Aggregation Group (LAG) at a time. The allocation mechan ism attempts to maximize aggregation, subject to management controls. Note: The path cost of a L AG port will be displayed as zero when it is n ot an active l ink. Each D-Series module provides 6 aggregator ports, which are designated in th e CLI as lag.0.1 through lag.0.6. LAG Link Aggregation Group. Once unde rlying physica l ports (for example, ge.x.x ) are associated with an aggregator port, the resulting aggre gation will be represented as o ne LAG with a lag.x.x port designation. D-Series LAGs can have up to associated physi cal ports. LACPDU Link Aggregation Control Protocol Data Unit. LACPDUs sent by the first party (the actor) convey to the second p arty (the actor ’s p rotocol p a rtner) what the actor knows, both about its own st ate and that of its p artner. Actor and Partner An actor is the local device sending LACPDUs. Its protocol partner is the device on the other end of the link aggregat io n. Each maintains current status of the other via LACPDUs containing information about their ports’ LACP status and operational state.

Admin Key V alue a ssigned to aggregator ports a nd physical ports that a re candidates for joining a LAG. The LACP implementation on D-Series devices will use this value to form an oper key and will determine which unde rlying physical ports are capable of aggregating by compar ing oper keys. Aggregator ports allow only underlying ports with oper keys matching theirs to join their LAG. On D- Series devices, the defaul t admin key value is 32768. System Priority V alue used to build a LAG ID, which determines aggregation precede nce. If there are two partner devices competing for the same aggregator, LACP compares the LAG IDs for each grouping of ports. The LAG with the lower LAG ID is given precedence and will be allowed to use th e aggregator. Note: Only one LACP system priority can be set on a D-Series device, using either the set lacp asyspri command ( page 4-38 ), or the set port lacp comma nd ( page 4-4 4 ). For information about. Refer to p age. show lacp 4-36 set lacp 4-38 set lacp a syspri 4-38 set lacp aadm inkey 4-39 clear lacp 4-39 set lacp static 4-40 clear lacp static 4-41 set lacp single portlag 4-41 clear lacp singleportlag 4-41 show port lacp 4-42 set port lacp 4-44 clear port lacp 4-45 Single Port LAGs Displays if the single port LAG feature ha s been enabled on the switch. See “ set lacp singleportlag ” on page 4-41 for more about single port LAG. Aggregator LAG port designation. Each D-Series module provides 6 virtual link aggrega tor ports, which are designa ted in the CLI as lag.0.1 through lag.0.6. Once underlying physical ports (for example, ge.x.x ) are associated with an aggregator port, the resulting Li nk Aggregation Group (LAG) is rep resented with a lag.x.x port designation. Actor Local device participat ing in LACP negotiatio n. Partner Remote device participating in LACP negotiation. System Identifier MAC addre sses for actor and partner. System Priority Syste m priority value which de termines aggregatio n prec edence.

Only one LACP system priority can be set on a D- Series device, using either the set lacp asyspri command ( page 4-38 ), or the set port lacp command ( page 4-44 ). Admin Key Port’s assigned key. D-Series devices pro vide a default admin key value of 32768 for all LAG ports (lag.0.1 though lag.0.6). Oper Key Port’ s operational key, derived from the admin key. Only underlying physical ports with oper keys matching the aggregator ’s will be allowed to aggregate. Attached Ports Underlying physical ports associated with this aggregator.If ports other than the desired underlying physical ports share the same admin key val ue, aggregation will fail or undesire d aggregations wil l form.Mode Switch ? command, ? read ? write. For information about. Refer to p age. set port protected 4-47 show port protected 4-48 clear port protected 4-48 set port pr otected name 4-49 show port protected name 4-49 clear port protected name 4-50 port.Refer to p age. SNMP Configuration Summary 5-1 Reviewing SNMP S tatistics 5-3 Configuring SNMP Users, Groups, and Communities 5-7 Configuring SNMP Access Rights 5-15 Configuring SNMP MIB Views 5-19 Configuring SNMP T arget Para meters 5-22 Configuring SNMP T arget Addresses 5-25 Configuring SNMP Notification Parameters 5-28 Creating a Basic SNMP Trap Configuration 5-37 AuthNoPriv MD5 or SHA None Provides auth entication based on the HMAC-MD5 or HMAC-SHA algorithms. authPriv MD5 or SHA DES Provide s authentication b ased on the HMAC-MD5 or HMAC-SHA algorithms. Provides DES 56-bit encryption in addition to authentication base d on the CBC- DES (DES-56) standard. T able 5-17 SNMP Security Levels ( Continued) Model Secu rity Level Authentication Encryption How It Works Refer to p age. show snmp engineid 5-4 show snmp counters 5-5 T able 5-18 show snmp engineid Output Det ails Output Fi eld What It Displays. EngineI d S t ring identifying the SNMP agent on the de vice. Engine Boot s Number of times the SNMP engine has been started or reinitialized.

Engine Time T ime in seconds since l ast reboot. Max Msg Size Maximum accepted length, in bytes, of SNMP frame. T able 5-19 show snmp counters Out put Det ails (Continued) Output Field What It Displays. Refer to p age. show snmp user 5-8 set snmp user 5-9 clear snmp user 5-10 show snmp group 5-1 1 set snmp group 5-12 clear snmp group 5-12 show snmp community 5-13 set snmp community 5-14 clear snmp community 5-14 list (Optional).Username SNMPv1 or v2 community name or SNMPv3 user name. Auth protocol T ype of authenticatio n protoc ol appli ed to thi s user. Privacy protocol Whether a priva cy protocol is applied when au thentication protocol is in use. S torage typ e Whether entry is stored in volatile, nonvolatile or read-only memory. Row status St atus of this entry: active, notInService, or notReady. Specifies ? a ? passw ord ? for ? th is ? user ? when ? authentication ? is ? required. ? Minimum ? of ? 8 ? characters. privacy ? privpassword (Optional). Applies ? encrypti on ? and ? specifies ? an ? encryption ? password. ? Minimum ? of ? 8 ? characters. Group name Name of SNMP group. Row status St atus of this entry: active, notInService, or notReady.Specifies ? a ? storage ? type ? for ? SNMP ? entrie s ? associated ? with ? the ? group. Specifies ? an ? SNMP ? securi ty ? name ? to ? associate ? with ? this ? community. conte xt ? context (Optional). Specifies ? the ? storage ? type ? for ? these ? entries. name Specifies ? the ? SNMP ? community ? name ? to ? clear. ? Refer to p age. show snmp access 5-15 set snmp access 5-17 clear snmp access 5-18 groupname (Optional). Displays ? access ? information ? for ? a ? speci fic ? security ? lev el. ? conte xt ? context (Optional).Security model Security model applied to this group. V alid types are: SNMPv1, SNMPv2c, and SNMPv3 (User based - USM ). Security level Security level applied to this gro up.Write V iew Name of the view that allows th is group to configure the contents of the SNMP agent.